Sonicwall 4060 pro manual

Will be starting to retire pretty soon here, though. Had great luck with Enhanced Mode, but ran into a serious issue, where the device kept rebooting. SonicWall sent new hardware out, but it failed in the same way.

Product - great. Support - Fail. However, I did have to upgrade to a Juniper shortly thereafter, which is far trickier to configure, but at least tech support stays on the line until it's working versus playing e-mail tag and getting nowhere. I could not be happier with SonicWall. There device and software just work. Their support is also top-notch. Whether you need help figuring out a settings or control or your scraping around for help for an internal network issue I have a site to site setup between two locations.

Browse by category. Ratings Breakout. To configure items in a submode, activate the submode by entering a command in the mode above it. For example, to set the default LAN interface speed or duplex, you must first enter configure , then interface x0 lan. To return to the higher Configuration mode, simply enter end or finished.

SonicWALL Internet Security appliances allow easy, flexible configuration without compromising the security of their configuration or your network. SonicWALL devices are shipped with a default password of password. Factory Reset to Defaults. If you are unable to connect to your device over the network, you can use the command restore to reset the device to factory defaults during a serial configuration session.

Follow the steps below to initiate a management session via a serial connection and set an IP address for the device. To ensure the best display and reduce the chance of graphic anomalies, use the same settings with the serial terminal software. The device terminal settings can be changed, if necessary.

Use the standard ANSI setting on the serial terminal software. Attach the other end of the null modem cable to a serial port on the configuring computer. Launch any terminal emulation application that communicates with the serial port connected to the appliance. Use these settings:. Note This option works for customers administering a device that does not have a cable for console access to the CLI.

Follow the steps below to initiate an SSH management session through an Ethernet connection from a client to the appliance.

Attach an Ethernet cable to the interface port marked XO. Attach the other end of the Ethernet cable to an Ethernet port on the configuring computer. Launch any terminal emulation application such as PuTTY that communicates via the Ethernet interface connected to the appliance. Within the emulation application, enter the IP destination address for the appliance and enter 22 as the port number.

Select SSH as the connection type and open a connection. Only the admin user will be able to login from the CLI. The default Admin username is admin.

The default can be changed. There is no lockout facility on the CLI. You can find suitable, free terminal emulators on the Internet. Note The default terminal settings on the firewall are 80 columns by 25 lines. To configure features using the CLI on a serial connection via the console port:. Attach the other end of the cable to a serial port on the configuring computer. Launch a terminal emulation application that communicates with the serial port connected to the appliance.

This option is useful for customers that do not have access to an RJ to DB-9 serial cable for the Console port on the firewall. Attach an Ethernet cable to the interface port marked X0. Launch a terminal emulation application or SSH client that communicates via Ethernet.

In the emulation application, enter the IP destination address for the X0 interface and enter 22 as the port number. Refer to the SonicOS 6. SafeMode is a limited Web management interface that provides a way to upload firmware from your computer and reboot the appliance. For instructions on how to restart your firewall in SafeMode, refer to the Getting Started Guide for your appliance.

Note In this example, the VPN policy on the other end has already been created. You may need to hit return two to three times to get to a command prompt, which will look similar to the following:. It has auto-complete so you do not have to type in the entire command. When you need to make a configuration change, you must be in configure mode.

To enter configure mode, type configure. The command prompt changes and adds the word config to distinguish it from the normal mode. Now you can configure all the settings, enable and disable the VPNs, and configure the firewall. In configure mode, create an address object for the remote network, specifying the name , zone assignment , type , and address.

In this example, we use the name OfficeLAN :. Note The prompt has changed to indicate the configuration mode for the address object. To display the address object, type the command show address-object [ name ] :. To create the VPN policy, type the command:. Note The prompt changes to indicate the configuration mode for the VPN policy. All the settings regarding this VPN will be entered here. Configure the Pre-Shared Key.

In this example, the Pre-Shared Key is sonicwall :. Define the local and the remote networks:. To enable the VPN policy, use the command vpn enable [ name ] :. Type the command show vpn policy. The output will be similar to the following:. To view the configuration for a specific policy, specify the policy name in double quotes.

For example:. Type the command s how vpn sa [ name ] to see the active SA:. GW: MAC Address. IP Address.